ASTM A240 UNS S32750 Alloy 2507 Sheet exporter in Mumbai
Industries, where the temperatures tend to be extreme, are prone to equipment failure. Especially if the incorrect material is used to produce said pieces of equipment. Super Duplex Plate supplier recommends using alloy 2507 as a material in their construction for several reasons. Not only does the material exhibit excellent performance at elevated temperature levels, but the ASTM A240 UNS S32760 Hr Plate can also service any application in temperatures as low as -50°C. At extreme temperature settings, it is quite common for plates and sheets to fail. In critical applications, failure of equipment often accompanies hazardous effects. To ensure success in such applications, using an ASTM specified A240 S32750 Shim Sheet is beneficial. Welding is altogether unavoidable in some applications, especially if they are to have a permanent joint.
2507 Super Duplex Plate
A240 UNS S32750 Sheet
ASTM A240 UNS S32760 Alloy 2507 Coil
ASME SA240 Grade 2507 Foil, ASTM A240 type 2507 Strip Manufacturer in india
A benefit offered by the Super Duplex 2507 Sheet is that this alloy is weldable without the use of any prior heat treatment, as required by some other stainless steel alloys. In comparison to several austenitic stainless steel alloys, the coefficient of thermal expansion for Super Duplex 2507 Plate is low. As a result of its low coefficient of thermal expansion, the residual stresses, as well as distortion in the 2507 Plate, see a reduction. The most common use of a UNS S32750 Plate is in pollution control, where equipment produced from this alloy is a part of the flue gas desulphurization process. And because the alloy has excellent resistance to chlorine stress related corrosion, the Super Duplex Plate is a part of marine and chemical processing applications.
Table of Content
Super Duplex Sheet Price per Kg
| Super Duplex 2507 Plate Cost | Price in US $ | Price in UAE Dirham |
|---|---|---|
| ASTM A240 Type 2507 Super Duplex Plate price per kg | US $ 8-US $ 10 | 30-37 UAE Dirham |
| ASTM A240 Type 2507 Super Duplex Sheet price per kg | US $ 9-US $ 13 | 34-48 UAE Dirham |
Differnt Types of Super Duplex Plate
2507 Super Duplex Stainless Steel Sheets
8mm Thick S32750 Super Duplex Stainless Steel Sheet Plates
Cold Rolled S32750 Super Duplex Stainless Steel Sheet
S32750 Super Duplex Stainless Steel Clad Plate
2507 Super Duplex 4mm Thick Stainless Steel Plate
20mm 2205 Super Duplex Stainless Steel Plates
Super Duplex 2507 S32750 Plates/sheet/coil
2507 Super Duplex Plate Sizes
| Size (in inches) | Size (in mm) |
|---|---|
| .125 | 3.18 |
| .134 | 3.40 |
| .156 | 3.96 |
| .187 | 4.75 |
| .250 | 6.35 |
| .312 | 7.92 |
| .375 | 9.53 |
| .500 | 12.7 |
| .600 | 15.9 |
| .750 | 19.1 |
| .875 | 22.2 |
| 1 | 25.4 |
| 1.125 | 28.6 |
| 1.250 | 31.8 |
| 1.500 | 38.1 |
| 1.750 | 44.5 |
| 2 | 50.8 |
| 2.500 | 63.5 |
| 3 | 76.2 |
We supply the 6mm-30mm UNS S32760 Super Duplex Sheet, check 1.5mm Alloy 2507 Shim and Circles thickness
Weight Chart of Super Duplex 2507 Sheet
| Thickness Chart in Inches | Plate Weight per Unit Area | Density |
|---|---|---|
| 3/16 | 0.06000 lbs/in²42.184176 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1/4 | 0.08 lbs/in²56.245568 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 3/8 | 0.121 lbs/in²85.0714216 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1/2 | 0.161 lbs/in²113.1942056 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 5/8 | 0.196 lbs/in²137.8016416 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 3/4 | 0.235 lbs/in²165.221356 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 7/8 | 0.274 lbs/in²192.6410704 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1 | 0.313 lbs/in²220.0607848 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1 1/4 | 0.391 lbs/in²274.9002136 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1 1/2 | 0.47 lbs/in²330.442712 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 1 3/4 | 0.549 lbs/in²385.9852104 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 2 | 0.627 lbs/in²440.8246392 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 2 1/4 | 0.705 lbs/in²495.664068 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 2 1/2 | 0.784 lbs/in²551.2065664 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 2 3/4 | 0.862 lbs/in²606.0459952 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
| 3 | 0.941 lbs/in²661.5884936 kg/m² | 0.315 lbs/in³8.72 g/cm³ |
ASME SA240 Grade 2507 Foil Dimension Table
| Plate Surface finish | Thickness (mm) | Width (max mm) |
|---|---|---|
| 2B – Cold rolled, heat treated, pickled, skin passed Sheet | 0.25–8.0 | 2032 |
| 2D – Cold rolled, heat treated, pickled Sheet | 0.4–6.35 | 1524 |
| 2E – Cold rolled, heat treated, mechanically descaled plate | 0.4–8.0 | 2032 |
| 2R – Cold rolled, bright annealed plate | 0.25–3.5 | 1524 |
| 2H – Work hardened plate | 0.4–6.35 | 1524 |
| Polished, brushed plate | 0.5–4.0 | 1524 |
A240 UNS S32750 Sheet Imperial Dimensions
| Plate Surface finish | Gauge (in) | Width (max in) |
|---|---|---|
| 2B – Cold rolled, heat treated, pickled, skin passed Plate | 10–24 | 72* |
| 2D – Cold rolled, heat treated, pickled plate | 12–24 | 60 |
| BA Mexinox only | 18–28 | 48 |
| Polished Sheet (not brushed) | 11–24 | 60 |
| Temper rolled Sheet Mexinox only | 13–29 | 48 |
Make An Inquiry To Buy Duplex 2507 Plate Manufacturers, UNS S32750 Hot and Cold Rolled Plate Properties. Super Duplex Plate Supplier in India
ASTM A240 type 2507 Strip Mechanical Behaviour
| Ultimate Tensile Strength, ksi | 116 min. |
|---|---|
| 0.2% Offset Yield Strength 0.2%, ksi | 80 min. |
| 0.1% Offset Yield Strength 0.2%, ksi | 91 min. |
| Elongation in 2 inches, % | 15 min. |
| Hardness Rockwell C | 32 max. |
| Impact Energy, ft.-lbs. | 74 min. |
UNS S32760 Super Duplex Sheet Chemical Composition
| C | Cr | Ni | Mo | N | Others |
|---|---|---|---|---|---|
| 0.020 | 25 | 7 | 4.0 | .27 | S=0.001 |
Properties of 2507 Super Duplex Sheet
| Density | lb/in3 | 0.28 |
|---|---|---|
| Modulus of Elasticity | psi x 106 | 29 |
| Coefficient of Thermal Expansion 68-212°F/°F |
x10-6/°F | 7.2 |
| Thermal Conductivity | Btu/h ft °F | 8.7 |
| Heat Capacity | Btu/lb/°F | 0.12 |
| Electrical Resistivity | W-in x 10-6 | 31.5 |
Super Duplex 2507 Plate Temperature Range
| Temperature °F | RT | 32 | -4 | -40 |
|---|---|---|---|---|
| Ft-lbs | 162 | 162 | 155 | 140 |
| Temperature °F | -76 | -112 | -148 | -320 |
| Ft-lbs | 110 | 44 | 30 | 7 |
| Temperature °F | 68 | 212 | 302 | 392 | 482 |
|---|---|---|---|---|---|
| 0.2% Offset Yield Strength, ksi | 80 | 65 | 61 | 58 | 55 |
| Ultimate Tensile Strength, ksi | 116 | 101 | 98 | 95 | 94 |
Toughness Chart of Duplex Stainless Steel Plate
| Temp. | -50°C | +20°C | -60°F | +70°F |
|---|---|---|---|---|
| Single | 75 J/cm_ | 90 J/cm_ | 54 ft. lbs | 65 ft. lbs |
| Average (5) | 90 J/cm_ | 150 J/cm | 65 ft. lbs | 87 ft. lbs |
Alloy 2507 Shim and Circles Hardness
| Average (5) | HV10 180-230 | HB : 180-230 | HRC _ 20 |
Duplex 2507 Plate Equivalent
| STANDARD | WERKSTOFF NR. | UNS |
| Super Duplex 2507 Plate / Sheet | 1.4410 |
S32750 / S32760 |
Density of UNS S32750 Hot and Cold Rolled Plate
|
UNS S32760 Super Duplex 2507 Plate density
|
0.28 lb/in3
|
Application of Super Duplex Stainless steel Plate
- Flue Gas Scrubbing Equipment
- Offshore Oil production/technology
- Oil and gas industry equipment
- Desalination Equipment
- Chemical process pressure vessels, piping and heat exchangers
- Pulp & Paper Mill Equipment
- Marine Applications
Melting Point of ASTM A240 type 2507 Perforated Sheet
|
ASTM A240 Type 2507 Super Duplex Plate melting range
|
2570 - 2660 °F (1410 - 1460 °C)
|
UNS S32750 / S32760 Plate Features
- Good general corrosion resistance
- High Strength
- High resistance to chloride stress corrosion cracking
- Superior resistance to chloride pitting and crevice corrosion
- Low rate of thermal expansion
- Good weldability and workability
- Combination of properties given by austenitic and ferritic structure
- Suggested for applications up to 600° F
We are leading Supplier of DIN 1.4410 Perforated Sheet, UNS S32750 / S32760 Plate Specification, 2507 Sheet price in Mumbai
2507 Sheet Spec Chart
| Specifications | ASTM A240 / ASME SA240 |
| Thickness | 4mm-100mm |
| Width |
1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc |
| Length | 2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc |
| Surface | 2B, 2D, BA, NO.1, NO.4, NO.8, 8K, mirror, checkered, embossed, hair line, sand blast, Brush, etching, etc |
| Finish | Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) |
| Form | Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange) etc. |
If you are looking to buy ASTM A240 TYPE 2507 Super Duplex Sheet from India first Check our shipments in last year
| Super Duplex 2507 UNS S32750 Cold Rollled Plate | France, Oman, Hong Kong, UAE |
| Super Duplex 2507 Sheet | Germany, Chile, Iran, Singapore |
| ASME SA240 Super Duplex Steel S32750 Strip Tape | USA, Netherlands, Romania, Ellington -United States |
| Hairline BA Mirror Finish 0.8mm Thick 2507 Super Duplex Plate | Italy, Philippines, Poland, Malaysia |
| 2507 Duplex Stainless Steel Sheet | Turkey, Europe, Canada, Dubai |
| super duplex 2507 hot rolled plate | Europe, United Arab Emirates (UAE), Norway, Malaysia |
| 2B HL No.4 mirror super duplex stainless steel sheet | Malaysia, Malaysia, Russia, UAE |
| Super duplex 2507 Sheet with BA surface | Saudi Arabia (KSA), Egypt, Malaysia, Singapore |
| Duplex 2507 Stainless Steel Cold Rolled Plate | South Africa, United Kingdom -UK, Los Alamos -Mexico, Malaysia |
| 2B Surface 2507 Super Duplex BBQ Plate | Australia, Sweden, NY 12203 (USA), China |
| 2507 Stainless Steel Sheet for Oil and gas industry | Malaysia, UK, Malaysia, Philippines |
| cold rolled s32750 super duplex sheet | Canada, Dammam -KSA, Philippines, Belgium |
| ASTM A240 Cold rolled Duplex steel 2507 Coil | Malaysia, Qatar, Europe, Thailand |
| 1.4410 Super Duplex 2507 Hot Rolled Plate | Japan, Czechia, Thailand, Malaysia |
| Super Duplex 2507 3mm Thick Coil | Colombia, Malaysia, Bangladesh, Finland |
| 2507 Stainless Steel Sheet | Taiwan, South Africa, Kuwait, Brazil |
| S32750 SAF 2507 stainless steel plate | South Korea, Bahrain, Singapore, Singapore |
| 2507 super duplex Checker Plate | Indonesia, Philippines, UK, Nigeria |
| NO 1 2B S32750 super duplex plate | Spain, Singapore, Mexico, UK |