Schedule 40 Carbon Steel Fittings, CS Fittings Weight Chart
In many industries, fittings are paired with pipes to form piping systems for multiple purposes. The main purpose of using Carbon Steel Pipe Fittings is to direct the flow of gas, steam, or liquid through the piping system. Some setups may require a change in direction, which is possible by the use of an elbow fitting. The most common angles produced by Carbon Steel Pipe Fittings Manufacturers In India would be at 45 degrees or at 90 degrees. Yet, the best part about fittings is that if the material is ductile enough, it is possible to customize the angle of the Carbon Steel Elbow Sch 40. So if an application were to call for a turn at 21.5 degrees, a manufacturer could produce the Carbon Steel 5d Elbow accordingly. Suffice to say, this is not the only function of Carbon Steel Weld Fittings. While a few fittings are involved in the directional change category, some others are allocated for flow regulatory purposes such as the Carbon Steel Reducer.
Carbon Steel Pipe Fittings
Carbon Steel Elbow Sch 40
Carbon Steel Buttweld Fittings
Check Sch 10 Low Carbon Steel 5d Elbow Weight Chart, 2" 3/4" sch 40 CS Reducer and Pipe End Cap Dimension
Reducers have one end that is the same dimension of the pipe in a system, and the other end is tapered such that it is one, or on some occasions two sizes smaller. Indirectly reducer Carbon Steel Buttweld Fittings lower the quantity of media flowing through a pipe. Though their main objective is to change into another pipe size that has either an increase or decrease in its outer diameter. Applications that require divergence at 90 degree angles may make use of a Carbon Steel Tee Fitting. Constructed in the shape of the letter T, this fittings has three openings at each point of the letter T.
Table of Content
Material Specification Chart of Carbon Steel Pipe Fittings
| ASTM SPECIFICATION A234 | ||
|---|---|---|
| Grade | WPA (Grade A) | WPB (Grade B) |
| Type of Steel | Carbon | Carbon |
| Chemical Composition | C-0.25 max. | C-0.30 max. |
| Minimum Physical Requirements | TS-48,000 / YP-30,000 | TS-60,000 / YP-35,000 |
| Heat Treatment | Cooled in Still Air | Cooled in Still Air |
DIN2609 Carbon Steel Tee Fitting manufacturer, Check 24 inch ASME SA234 CS 90 degree Elbow and 180 Deg Bend Specification
Carbon Steel Weld Fittings Spec Chart
| Specifications | A234 WPB / A420 WPL3 / A420 WPL6 / MSS-SP-75 WPHY 42 / 46 / 52 / 56 / 60 / 65 / 70. |
| Standards Chart | ANSI/ASME B16.28, B16.9, MSS-SP-43. |
| Size in Inch | ½"NB to 48″NB in Sch 10s, 40s, 80s, 160s, XXS. |
| Schedules | Sch.40 to Sch.XXs |
| Type | Seamless / Welded / Fabricated |
| Pipe Fittings Products | Long Radius Elbow, Short Radius Elbow, Bends in 3D, 5D, 10D, 20D in 45 Deg, 90 Deg, 180 Deg (Return Bends) or as per the requirement, Equal Tee, Unequal Tee, Concentric Reducer, Eccentric Reducer, Stub-Ends, Cap, Collar, Cross, Insert. |
Various Types Of Carbon Steel Buttweld Fittings
ASME B16.9 90d Elbow Carbon Steel ButtWeld Pipe Fitting
Carbon Steel Sch 40 Fittings
Schedule 10 Carbon Steel Pipe Fittings
ASTM A420 Carbon Steel Pipe Reducer, CS Tee
CS Fittings Material
Carbon Steel Butt Welding Pipe Fitting
Carbon Steel Schedule 80 Pipe Fittings
Carbon Steel Schedule 10 Fittings
Carbon Steel Grooved Fittings
B16.28 Carbon Steel Seamless Pipe Fittings
23 Inch DN450 x DN200, Butt Welded, Carbon Steel Seamless Pipe Fittings
MSS SP 75 Carbon Steel Buttweld Fittings, 6 Inch 8 Inch CS Equal and Reducing Tee at factory Price.
Carbon Steel Fittings Price List Prices
| Carbon Steel Pipe Fittings Price Per Piece in India | Price in INR | Price in USD | Price in UAE Dirham |
| CS FITTINGS SA 420 GR.WPL6 DN 400X350,SCH XS,CONCENTRIC REDUCER ,BUTT WELD | 575 | $7.81 | UAE Dirham 28.68 |
| CARBON STEEL SEAMLESS PIPE FITTINGS (ASTM A234 WPB 90 ELBOW B16.9 SMLS SIZE 16 SCH20) | 35 | $0.48 | UAE Dirham 1.75 |
| CS WELDED PIPE FITTINGS (ASTM A234 WPB CON. REDUCER B16.9 SMLS SIZE 10X6 SCH40) | 35 | $0.48 | UAE Dirham 1.75 |
| CS ASTM A234 WPB TEE B16.9SMLS SIZE 2X1 SCH80) | 44 | $0.60 | UAE Dirham 2.19 |
| PIPE FITTINGS CARBON STEEL SA 420 GR.WPL6 DN 300X200,SCH 120,ECCENTRIC REDUCER ,BUTT WELD | 584 | $7.93 | UAE Dirham 29.13 |
Carbon Steel Reducer Standards
|
Carbon Steel (B/W) Fittings
|
||||
|
Materials
|
Size Chart
|
Schedule & Swg.
|
Specification Chart
|
Carbon steel Piping materials
|
|
Carbon STeel
|
15
to 500 Nominal Bore |
Schedule 40
to Schedule XXs |
A234 WPB Buttweld
Seamless ANSI B16.9 |
CS Bend (Short & Short)
CS Elbow ( 90o,180o, 45o) CS Tee (UnEqual & equal) CS Reducer (Concentric & Eccentric) CS CAP CS Stubend (Short & Long) CS Nipple (Barrel) |
|
200
to 600 Nominal Bore |
Schedule 10
to schedule 80s |
A234 WPW Buttweld
Welded ANSI B16.9 |
||
|
Low Temp Carbon Steel
|
15 NB
to 300 NB |
Sch. 5
to Sch. 80s |
A403 B/W
ANSI B16.9 |
|
|
200 NB
to 600 NB |
Sch. 10
to Sch. 80s |
A420 WPL 6 B/W
Welded ANSI B16.9 |
||
CS Pipe Fittings Manufacturers In India, Check Bevel Ends Carbon Steel Weld Fittings Mechanical Properties
CS Pipe Fittings Mechanical Properties Chart
|
Property
|
Values
|
|
Ultimate Tensile Strength *
|
95 min Ksi (655 Mpa)
|
|
0.2 % Yield Strength *
|
75 min Ksi (517 Mpa)
|
|
Elongation *
|
17 % min
|
|
Reduction of Area *
|
35 % min
|
|
Charpy Impact Toughness
|
42 mean/ 33 min J at –18o C
|
|
Hardness
|
197 – 237 BHN (75 Ksi min)
|
Thickness Chart Of Carbon Steel Elbow Sch 40
| Nominal Pipe Size | Wall Thickness* | ** Working Pressure– lbs per square inch at the Fahrenheit Temperature Indicated |
|||
| -20 to 650 | 700 | 750 | *** 800 | ||
| 1/2 | 0.109 | 1695 | 1621 | 1463 | 1220 |
| 3/4 | 0.113 | 1455 | 1392 | 1256 | 1046 |
| 1 | 0.133 | 1575 | 1506 | 1359 | 1134 |
| 1 1/4 | 0.140 | 1065 | 1019 | 919 | 766 |
| 1 1/2 | 0.145 | 1005 | 960 | 867 | 723 |
| 2 | 0.154 | 900 | 861 | 777 | 648 |
| 2 1/2 | 0.203 | 1215 | 1162 | 1048 | 874 |
| 3 | 0.216 | 1095 | 1047 | 945 | 788 |
| 3 1/2 | 0.226 | 1020 | 975 | 880 | 734 |
| 4 | 0.237 | 975 | 932 | 841 | 702 |
| 5 | 0.258 | 885 | 846 | 764 | 637 |
| 6 | 0.280 | 840 | 803 | 725 | 604 |
| 8 | 0.322 | 765 | 731 | 660 | 550 |
| 10 | 0.365 | 720 | 688 | 621 | 518 |
| 12 | 0.375 | 630 | 602 | 543 | 453 |
| 14 | 0.375 | 570 | 545 | 492 | 410 |
| 16 | 0.375 | 495 | 473 | 427 | 356 |
| 18 | 0.375 | 450 | 430 | 388 | 354 |
| 20 | 0.375 | 405 | 387 | 349 | 291 |
| 24 | 0.375 | 330 | 315 | 284 | 237 |
| 30 | 0.375 | 265 | 254 | 229 | 190 |
| 36 | 0.375 | 220 | 198 | 178 | 148 |
| 42 | 0.375 | 189 | 181 | 163 | 136 |
| 48 | 0.375 | 165 | 158 | 143 | 118 |
Composition Chart of Sch 10 Low Carbon Steel 5d Elbow
|
Element
|
Weight %
|
|
Carbon
|
0.08 – 0.15
|
|
Silicon
|
0.15 – 0.50
|
|
Manganese
|
0.30 – 0.60
|
|
Phosphorus
|
0.025 max *
|
|
Sulphur
|
0.025 max *
|
|
Molybdenum
|
0.90 – 1.10
|
|
Chromium
|
2.00 – 2.50
|
|
Nickel
|
0.5 max
|
CS Fittings Pressure Rating Standard
| Nominal Pipe Size | Wall Thickness* | ** ** Working Pressure– lbs per square inch at the Fahrenheit Temperature Indicated | |||
| -20 to 650 | 700 | 750 | *** 800 | ||
| 1/2 | 0.147 | 3030 | 2898 | 2615 | 2181 |
| 3/4 | 0.154 | 2595 | 2482 | 2240 | 1868 |
| 1 | 0.179 | 2610 | 2496 | 2253 | 1879 |
| 1 1/4 | 0.191 | 1935 | 1851 | 1670 | 1391 |
| 1 1/2 | 0.200 | 1815 | 1736 | 1566 | 1306 |
| 2 | 0.218 | 1665 | 1592 | 1437 | 1198 |
| 2 1/2 | 0.276 | 1935 | 1851 | 1670 | 1393 |
| 3 | 0.300 | 1770 | 1693 | 1528 | 1274 |
| 3 1/2 | 0.318 | 1665 | 1592 | 1437 | 1198 |
| 4 | 0.337 | 1590 | 1521 | 1372 | 1144 |
| 5 | 0.375 | 1470 | 1406 | 1269 | 1058 |
| 6 | 0.432 | 1470 | 1406 | 1269 | 1058 |
| 8 | 0.500 | 1350 | 1291 | 1165 | 972 |
| 10 | 0.500 | 1065 | 1018 | 919 | 766 |
| 12 | 0.500 | 900 | 861 | 777 | 648 |
| 14 | 0.500 | 810 | 774 | 699 | 583 |
| 16 | 0.500 | 705 | 674 | 608 | 507 |
| 18 | 0.500 | 630 | 602 | 543 | 453 |
| 20 | 0.500 | 570 | 545 | 492 | 410 |
| 24 | 0.500 | 465 | 444 | 401 | 334 |
| 30 | 0.500 | 377 | 362 | 326 | 270 |
| 36 | 0.500 | 314 | 301 | 272 | 225 |
| 42 | 0.500 | 269 | 258 | 232 | 193 |
| 48 | 0.500 | 235 | 226 | 203 | 169 |
Size Chart of CS Reducer
| Products | Sizes |
| ASME B16.11 CS Elbow | 1/2'' NB to 14'' NB |
| Carbon steel Reducers | 1'' NB to 14'' NB |
| Sch 40 CS Tee | 1'' NB to 14'' NB |
| CS Cups | 1/2'' NB to 14'' NB |
| ASME A234 Carbon Steel Stub Ends | 1/2'' NB to 14'' NB |
| MSS-Sp-43 CS Socket Weld | Up to 2'' NB |
| Carbon Steel Nipple | Up to 4'' |
| ASTM A420 Carbon Steel Coupling | Up to 4''NB |
An Indian Manufacturer but Global supplier, check what and where
| ASME B16.9 carbon steel pipe fittings | South Africa, Bahrain, Singapore |
| schedule 10 cs pipe fittings | France, Thailand, Europe, Qatar |
| 26 Inch carbon steel buttweld fittings | Philippines, Nigeria, Australia, UK |
| SCH 120, LTCS, CS buttweld Fittings | Oman, Malaysia, Hong Kong, UAE |
| carbon steel reducer | Finland, Malaysia, USA, Bangladesh |
| DN450 x DN200 CS Grooved Fittings | Italy, Iran, Chile, Singapore |
| 6 x 4 Inch, BW, ASME B16.9 carbon steel buttweld caps | United Arab Emirates (UAE), Norway, Malaysia, Turkey |
| carbon steel swage fittings | Dammam -KSA, Indonesia, Belgium, Philippines. |
| carbon steel stub end & concentric reducer | Canada, Singapore, Malaysia, Philippines |
| CL3000, DN25, SW, ASME B16.11, Carbon Steel Forged Fittings | Egypt, Spain, UK, Mexico |
| galvanized carbon steel connector | Ellington -United States, Poland, Canada, UK |
| carbon steel buttweld pipe fittings | United Kingdom -UK, Europe, UAE, Malaysia |
| low carbon steel fittings | Japan, Europe, Romania, Malaysia |
| carbon steel weld fittings | Germany, Czechia, Malaysia, Thailand |
| SCH 80, killed CS Fittings | Colombia, Malaysia, Sweden, China |
| 2 Inch x 1 Inch, BW, SCH 30 low temp CS elbow | Dubai, Netherlands, Russia, Malaysia |
| CS tee & pipe cap | South Africa, Saudi Arabia (KSA), Kuwait, Brazil |